How-to
How to Make an Activated Charcoal Face Mask with White Kaolin Clay
A charcoal face mask is a clay mask with a pinch of charcoal in it. Here are the amounts, the steps, when to rinse, and how to keep the black off your sink and towels.
The short answer: Stir ⅛ teaspoon of activated charcoal into 2 teaspoons of white kaolin clay, add about 2 teaspoons of water and mix to a paste like thin yoghurt. Spread a thin layer on clean skin, leave it for 5–10 minutes at most and rinse before it hardens. Use it once a week.
What do you need for a charcoal face mask?
You need white kaolin clay, activated charcoal powder, water, and a clean, dry non-metallic bowl and spoon. The amounts for one mask:
| Ingredient | Amount |
|---|---|
| White kaolin clay | 2 teaspoons |
| Activated charcoal powder | ⅛ teaspoon |
| Cool or room-temperature water | about 2 teaspoons |
Have a dark towel ready as well. This mask uses Spierb Activated Bamboo Charcoal Powder with Spierb White Kaolin Clay as the base. Keep the charcoal small. A pinch goes through the whole mask, and more doesn't make a better one.
Why does charcoal need a clay base?
Because charcoal doesn't dissolve in water or thicken it. Stirred into water alone, it spreads out as tiny black particles and makes a runny slurry that separates and goes on unevenly. Kaolin clay gives the mask its body: a smooth paste that stays where you put it and rinses off cleanly.
What should you do before your first mask?
Patch test 24–48 hours before your first mask, with the same mixture you plan to use. Put a little on a small area of clean, unbroken skin, leave it only as long as you would wear the mask, rinse it off and watch the spot for 24–48 hours. Don't go ahead if the skin burns, swells, blisters or turns red, or if it itches and the itch doesn't settle. A patch test can't rule out a reaction later.
Don't use the mask on broken, sunburnt or irritated skin.
How do you make and apply the mask, step by step?
Mix the two powders dry, add water gradually, and rinse the mask while it is still pliable.
- Wash your face and pat it dry.
- Put 2 teaspoons of kaolin and ⅛ teaspoon of charcoal in your bowl. Scoop the charcoal gently and stir slowly, so black dust doesn't rise.
- Add the water a little at a time and mix to a smooth paste like thin yoghurt.
- Leave it for 1–2 minutes, then stir again. Add a few drops of water if it has thickened.
- Spread a thin, even layer on clean skin, avoiding your eyes, the eye area and your lips. On combination skin, use it on oily areas only.
- Leave it on for 5–10 minutes at most. If your skin is dry or reactive, start at 3–5 minutes.
- Rinse while the mask is still pliable, before it turns hard, very tight or cracked. Go by feel, because the black hides the usual colour change as clay dries.
- Wet your face with lukewarm water, loosen the mask with your fingertips and rinse. Don't scrub.
- Pat dry and moisturise. Throw away any leftover paste.
Rinse it off and stop if your skin burns, stings or keeps itching. Keep the mask away from your eyes, and rinse with plenty of clean water if any gets in.
How long do you leave it on, and how often can you use it?
Leave it on for 5–10 minutes at most, and use it once a week. Use it less often if your skin feels dry afterwards. The mask picks up surface oil while it is wet and setting, so letting it dry hard adds nothing but tightness.
What should you expect?
A smooth grey-black paste with almost no smell, and skin that feels clean and less shiny after rinsing. The finish shows straight away and usually lasts for some hours. Charcoal doesn't stain skin. If you find black specks along the hairline or in creases, wet the area again and rinse gently.
How do you keep charcoal off the sink and towels?
Rinse the sink straight away and use a dark towel. Charcoal may stain fabrics and porous surfaces. Wipe up dry spills while they are still dry, since water spreads them. Close the pouch after scooping, and keep the powder away from pale worktops and grout.
What are the common mistakes?
Most problems come down to the layer, the timing or the rinse.
- Too much charcoal. ⅛ teaspoon is the full amount for one mask.
- Mixing charcoal with water alone. It makes a thin slurry. Use the clay base.
- Rubbing dry powder into the skin. It is always mixed into a paste first.
- Waiting for a colour change. Black masks don't show one. Go by time and feel.
- Scrubbing it off. Wet it, loosen it with your fingertips and rinse.
Frequently Asked Questions
What should I put on my face after a charcoal mask?
Your usual moisturiser, especially if your skin feels tight. Leave scrubs, peels and other exfoliating products for another day.
What happens when you mix charcoal powder with water?
It doesn't dissolve. It spreads through the water as fine black particles and slowly settles, which makes a runny slurry. That is why the mask uses a kaolin clay base.
Can I rub charcoal on my face?
No. Don't rub the dry powder into your skin. Mix it into the clay paste, spread a thin layer and rinse it off gently.
Does charcoal really remove blackheads?
In a clay mask it picks up oil and residue at the surface, which can make pores look less noticeable for a while. Do clay masks remove blackheads? explains what it can and can't do.
Can I use it in a body scrub or in soap?
Yes. Charcoal is also used in a body scrub with Walnut Shell Powder and in handmade soap. The amounts are in the Complete Mixing and Application Guide that comes with your pack. The body scrub is never used on the face.
Can I use it on my teeth?
No. Spierb Activated Bamboo Charcoal Powder is not for teeth, gums or anywhere in the mouth, and it is not for eating or drinking.
