How-to
How to Use Alum Powder on Your Face: The Rinse and the After-Shave
Alum powder is used on the face as a weak solution, for under a minute, then rinsed off. Here are the two strengths, the steps for each, and how often to use them.
The short answer: Dissolve ⅛ level teaspoon of alum granules in 100 ml of water, wipe it over clean skin with a cotton pad, leave it for 30–60 seconds and rinse it off. Use it once a week, or up to twice. As an after-shave, use ¼ level teaspoon in 100 ml in the same way.
What do you need to use alum powder on your face?
You need alum granules, 100 ml of clean water, a clean glass or cup, a level measuring spoon and a cotton pad. There are two strengths:
| Use | Alum granules | Water | On the skin |
|---|---|---|---|
| Face and body rinse | ⅛ level teaspoon | 100 ml | 30–60 seconds, then rinse |
| After-shave | ¼ level teaspoon | 100 ml | 30–60 seconds, then rinse |
Slightly warm water helps the granules dissolve. Spierb Alum Powder is 100% potassium alum, the same ingredient as an alum block, in loose granules. The granules are always dissolved first and never rubbed on the skin.
What should you do before your first use?
Patch test 24–48 hours before your first use, at the strength you plan to use. Mix a small amount of solution, put it once on a small area of clean, unbroken skin, rinse it off after 30–60 seconds and watch the spot for 24–48 hours. Don't go ahead if the skin burns, swells, blisters or turns red, or if it itches and the itch doesn't settle. A patch test can't rule out a reaction later.
Throw the test solution away and make a fresh one on the day you start.
How do you use alum powder as a face rinse, step by step?
Dissolve it, wipe it on, wait 30–60 seconds and rinse.
- Wash your face and pat it dry.
- Measure ⅛ level teaspoon of granules into 100 ml of water.
- Stir until the crystals have completely dissolved.
- Wet a cotton pad with the solution and wipe a small amount over clean skin, avoiding your eyes and lips.
- Leave it for 30–60 seconds.
- Rinse your face with water and pat it dry.
- Moisturise if your skin needs it.
Rinse it off and stop if your skin burns, stings or keeps itching. Keep the solution away from your eyes, and rinse with plenty of clean water if any gets in.
The same rinse can be used on clean, unbroken, oily-feeling body skin such as the back, chest or shoulders, for the same 30–60 seconds.
How do you use alum as an after-shave?
Use the slightly stronger solution: ¼ level teaspoon in 100 ml of water.
- Finish shaving and rinse your skin with cool or lukewarm water.
- Pat gently. Your skin can stay slightly damp.
- Apply a thin layer of the solution with clean hands or a cotton pad, avoiding your lips and nostrils.
- Leave it for 30–60 seconds.
- Rinse with cool water and pat dry.
- Apply a simple moisturiser or after-shave balm if you like.
A brief, light sting on freshly shaved skin is normal. If it stings strongly, rinse at once and leave that area alone until the skin has recovered. Don't use it on deep cuts or broken skin.
How long can you leave alum on your face?
30–60 seconds, then rinse. Alum is an astringent, and a short contact is all it takes for skin to feel fresh and less greasy. Longer doesn't do more; it only dries the skin. It is never left on the face overnight.
Should you wash your face after applying alum?
Yes. Rinse with plain water after 30–60 seconds, both for the face rinse and after shaving. You don't need a cleanser, just water. Then pat dry and moisturise if your skin feels tight.
How often should you use it, and what should you expect?
Use the face rinse once a week, or up to twice a week if your skin stays comfortable. The solution is clear and has no smell. Skin usually feels fresh, less greasy and a little tighter for a while afterwards. That feeling is temporary. Alum doesn't take up oil the way a clay does, and it isn't a daily toner.
What are the common mistakes?
Most problems come from using alum too strong, for too long or too often.
- Rubbing granules on the skin. Loose crystals scratch. Always dissolve them.
- Making it stronger. A stronger solution doesn't work better on the face; it dries and stings.
- Keeping the solution. Make it fresh, use it the same day and throw away what is left. A kept solution starts to form crystals again.
- Using it every day. Once or twice a week is the limit for the face.
- Using it on spots or sore skin. Keep it off broken, picked, inflamed or already dry and tight skin.
Frequently Asked Questions
How often should I use alum on my face?
Once a week, or up to twice a week if your skin stays comfortable. It isn't a daily product for the face.
Can I leave alum on my face overnight?
No. Leave it on for 30–60 seconds and rinse it off. Left on, it dries the skin.
Do I rinse my face after using an alum block?
Yes. A wet alum block leaves the same alum solution on the skin as dissolved granules do, so rinse after a short while in the same way.
Can I use alum on my underarms every day?
Alum is also used as an underarm deodorant, and that is the one use where it is applied daily and left on. Its strength and method are in the Complete Mixing and Application Guide that comes with your pack.
Can I use alum on my face every day, and what are the downsides?
Not every day. Used too often or too strong, alum leaves skin dry, tight and irritated. Is alum safe for skin? covers the limits.
